Ace NACE-CIP1-001 Certification with 100 Actual Questions
PASS NACE NACE-CIP1-001 EXAM WITH UPDATED DUMPS
NEW QUESTION # 44
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Rotating the dial too fast when taking measurements
- B. Failing to determine the base metal reading (BMR)
- C. Taking measurements too far from the edge of a surface
- D. Measuring ditty, tacky, or soft films
Answer: A,B,D
NEW QUESTION # 45
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Localized Corrosion
- B. Atmospheric Corrosion
- C. Galvanic Corrosion
- D. General Corrosion
Answer: C
NEW QUESTION # 46
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. Pass/fail criteria
- B. A final conflict resolution method
- C. A method to grade surface profile
- D. A general guide
Answer: D
NEW QUESTION # 47
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Dragging a gauge through wet coating
- B. Using a damaged gauge
- C. Placing the gauge along the longitudinal axis
Answer: A,B
NEW QUESTION # 48
Osmotic blistering is most likely to occur as a result of
- A. inadequate anchor pattern/surface profile.
- B. overcoating a surface contaminated with chemical salts.
- C. airless spray application
- D. applying tine coating too thin.
Answer: C
NEW QUESTION # 49
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- B. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- C. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- D. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
Answer: D
NEW QUESTION # 50
If inspectors identify issues of non-conformance during an inspection, they should
- A. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- B. perform additional tests secretly to ensure there are no other potential issues at the site
- C. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- D. wait until the final report is being prepared to identify the issues in writing so they are fully documented
Answer: C
NEW QUESTION # 51
The NACE Inspector should perform tests for soluble salts:
- A. After surface preparation
- B. Prior to coating application
- C. Prior to surface preparation
- D. When specified
Answer: D
NEW QUESTION # 52
ISO SA 2.5 is defined as:
- A. Thorough Blast Cleaning
- B. Very Thorough Blast Cleaning
- C. Light Blast Cleaning
- D. Near White Metal Blasting
Answer: B
NEW QUESTION # 53
Removal of welds splatter is required:
- A. When NACE/SSPC abrasive blast standards are specified
- B. When ISO abrasive blast standards are specified
- C. On every job
- D. When specifically identified in the owner's specification
Answer: D
NEW QUESTION # 54
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 70% of the specified maximum thickness
- B. 100% of the specified maximum thickness
- C. 80% of the specified minimum thickness
- D. 90% of the specified maximum thickness
Answer: C
NEW QUESTION # 55
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION # 56
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Abrasive blast nozzles
- B. Hand tools
- C. Airless spray equipment
- D. Power tools
Answer: D
NEW QUESTION # 57
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. cracking.
- B. holiday.
- C. sagging.
- D. checking.
Answer: B
NEW QUESTION # 58
To achieve consistently accurate results with ALL alt test equipment
- A. calibrate the instrument in the field.
- B. wear gloves when sampling.
- C. wash your hands before sampling.
- D. avoid placing the sample discs on a surface.
Answer: C
NEW QUESTION # 59
Relative humidity is
- A. the lowest temperature at which moisture forms on a steel surface.
- B. the highest temperature at which moisture forms on a steel surface.
- C. a measure of the amount of moisture in the air compared to saturation level.
- D. a measure of the amount of moisture in the air compared to the air temperature.
Answer: C
NEW QUESTION # 60
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. vial lest.
- B. wet film thickness (WFT) measurement.
- C. blotter test for the presence of oil and water.
- D. dry film thickness (DEI) measurement.
Answer: C
NEW QUESTION # 61
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Bring the matter up at the pre-job conference
- B. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- C. Default to the owner's Inspection and Test Plan
- D. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
Answer: A
NEW QUESTION # 62
Which one of the following documents is the best source for coating technical data:
- A. Application Guidelines
- B. Safety Data Sheet;
- C. Specification
- D. Technical Data Sheet
Answer: D
NEW QUESTION # 63
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which power tool the Contractor selects
- B. Yes, because the 'two standards are not equivalent
- C. It depends on which hand tool the Contractor selects
- D. No, because there is no real difference in the standards
Answer: D
NEW QUESTION # 64
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. white metal blast cleaning.
- B. brush-off blast cleaning.
- C. commercial blast cleaning.
- D. near-white metal blast cleaning.
Answer: B
NEW QUESTION # 65
ASTM Standards are applicable:
- A. In North America
- B. In Asia
- C. When specified
- D. In the USA
Answer: C
NEW QUESTION # 66
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor of your readings
- B. Advise the Contractor he can proceed
- C. Advise the Contractor he cannot proceed
- D. Call your supervisor
Answer: A
NEW QUESTION # 67
The main responsibilities of the inspector are to
- A. observe and report the quality of the work performed.
- B. direct and perform the work stated in the specification.
- C. observe and direct the work of the contractors.
- D. demonstrate to the contractor how to apply the coating.
Answer: A
NEW QUESTION # 68
......
NACE-CIP1-001 Questions PDF [2023] Use Valid New dump to Clear Exam: https://www.lead1pass.com/NACE/NACE-CIP1-001-practice-exam-dumps.html
Passing NACE NACE-CIP1-001 Exam Using 2023 Practice Tests: https://drive.google.com/open?id=1g-8Vob0NXXB1lwyH-G3Vh-MXOWjyMxtJ