D-SNC-DY-00 PDF Download Jan-2025 EMC Test To Gain Brilliante Result!
Provide Updated EMC D-SNC-DY-00 Dumps as Practice Test and PDF
NEW QUESTION # 26
What is the purpose of the write erase boot command option?
- A. Delete the startup and enable zero touch provisioning.
- B. Remove user-installed packages and tile changes.
- C. Delete the running configuration and all user accounts.
- D. Delete the startup configuration and the management interface configuration.
Answer: A
Explanation:
The write erase boot command option deletes the startup configuration and enables zero touch provisioning (ZTP). This is used to reset the switch to its default state and prepare it for automated configuration through ZTP.
References:
* Dell Technologies SONiC Command Reference Guide
* Switch Configuration Guide
NEW QUESTION # 27
Refer to the exhibits.
PC1 has a valid address on the 192.168.10.0 network, and PC2 has a valid address on the 192.168.20.0 network.
What happens when a ping command is issued between PC1 and PC2?
- A. The ping is successful because there are two routes from switch1 to switch2 which are connected to PC2.
- B. The ping is unsuccessful because there is no route to the VLAN 10 gateway address of 192.168.10.254.
- C. The ping is successful because there is a route to 10.0.1.1, which is connected to 1(10.2.2, which is connected to PC2.
- D. The ping is unsuccessful because there is no route from switch 1 to the 192.168.20.0 network.
Answer: D
Explanation:
* Network Topology Analysis:
* PC1 is on VLAN 10 with an IP address in the 192.168.10.0/24 subnet.
* PC2 is on VLAN 20 with an IP address in the 192.168.20.0/24 subnet.
* The network uses OSPF for routing between the switches.
* The OSPF area is 0, and all switches have loopback interfaces for OSPF.
* Routing Table Examination (from switch1):
* The show ip route command output from switch1 provides a detailed look at the routing table.
* Routes to the 192.168.10.0/24 network (directly connected via Vlan10) are present.
* No routes to the 192.168.20.0/24 network are listed in switch1's routing table.
* Explanation:
* For PC1 to communicate with PC2, switch1 must have a route to the 192.168.20.0/24 network.
* The absence of a route to the 192.168.20.0/24 network in switch1's routing table means that switch1 cannot forward packets destined for 192.168.20.0/24.
* Therefore, any ping from PC1 to PC2 will be unsuccessful as switch1 does not know how to route packets to PC2's network.
* Verification with Dell SONiC:
* In Dell SONiC environments, OSPF is configured to ensure dynamic routing.
* The configuration must include all necessary networks for inter-switch routing.
* If a network (like 192.168.20.0/24) is not included in OSPF configurations on switch1, routes to that network will not be advertised or learned, leading to failed connectivity tests like the ping from PC1 to PC2.
References:
* Dell Enterprise SONiC Deployment Guide
* Dell Technologies Networking - SONiC
NEW QUESTION # 28
What interface must be selected when configuring the management port from within the MF-CLI environment?
- A. ma 0/1
- B. eth0
- C. mgmt 1/1/1
- D. Management 0
Answer: B
Explanation:
* Dell SONiC Management Interface Configuration:
* In Dell SONiC, the management port configuration is a crucial aspect that allows administrators to access and manage the network device.
* The management interface typically provides out-of-band management access to the device, ensuring that even if the data network is down, the management network can still be accessed.
* Common Interface Naming Conventions:
* mgmt 1/1/1: This naming convention is not typically used in Dell SONiC environments for management interfaces.
* ma 0/1: This could be a potential naming convention but is not standard for Dell SONiC.
* Management 0: This is a logical name but does not align with the standard interface naming conventions used in Dell SONiC.
* eth0: This is the standard naming convention used for the primary management interface in most Linux-based systems, including Dell SONiC.
* Verification with Dell SONiC Documentation:
* Dell SONiC documentation specifies that the management interface is usually named eth0.
* When accessing the management interface within the MF-CLI (Management Framework Command Line Interface) environment, eth0 is the correct interface to configure.
* Practical Configuration Example:
* When configuring the management port, the command might look something like:
config interface ip add eth0 <management_ip_address>/<subnet_mask>
* This command specifies the management interface eth0 and assigns it an IP address for network management purposes.
References:
* Dell Enterprise SONiC Deployment Guide
* Dell Technologies Networking - SONiC
This detailed step-by-step explanation confirms that the correct answer is D, providing insights into the typical interface naming conventions and configuration practices within the Dell SONiC environment.
NEW QUESTION # 29
What are two characteristics of route maps in Enterprise SONIC?
- A. Each route map clause has the type values of Match. Set. and Act.
- B. The permit or deny clause In route maps permits or rejects the matching routes from being redistributed.
- C. They are a series of commands that contain a matching criterion and action.
- D. Route-map names are not case-sensitive.
Answer: B,C
Explanation:
Route maps in Enterprise SONIC are used for controlling and modifying routing information. They contain a series of commands with matching criteria and actions. The permit or deny clause within route maps determines whether the matching routes are permitted or denied from being redistributed.
References:
* Dell Technologies SONiC Route Map Configuration Guide
* Dell Networking Configuration Guide
NEW QUESTION # 30
What does show interface breakout port slot/slot command display?
- A. The configuration of that port
- B. The In Progress/Complete status of the breakout of the port
- C. The Error/Debug status of the breakout of the port
- D. The breakout modes available to that port
Answer: D
Explanation:
The show interface breakout port slot/slot command displays the breakout modes available for the specified port. Breakout modes determine how a single high-speed port can be split into multiple lower-speed ports, providing flexibility in network port configurations.
References:
* Dell Technologies SONiC Command Reference Guide
* Port Breakout Configuration Guide
NEW QUESTION # 31
Which two things does the no vrrp 100 address-family ipv6 command delete?
- A. Interface
- B. Version
- C. Authentication
- D. Address-family
- E. Identifier
Answer: D,E
Explanation:
The no vrrp 100 address-family ipv6 command deletes the VRRP (Virtual Router Redundancy Protocol) identifier (A) and the address-family configuration (D) for VRRP group 100. This effectively removes the VRRP configuration for the specified address family.
References:
* Dell Technologies SONiC documentation
* VRRP Configuration Guide
NEW QUESTION # 32
Configure a VRF called "VrfGreen" and the static route in it to network 172.16.128.64/28 through next-hop
10.10.10.1. Set an administrative distance of 213.
Answer:
Explanation:
see the explanation for all step by step solution with all explanation.
Explanation:
Here are the steps to configure the VRF and the static route:
* Enter Configuration Mode:
sonic# configure terminal
* Create VRF "VrfGreen":
sonic(config)# ip vrf VrfGreen
* Configure the Static Route:
sonic(config)# ip route vrf VrfGreen 172.16.128.64/28 10.10.10.1 213
* Save Configuration:
sonic# write memory
Comprehensive Detailed Step by Step Explanation with References:
* Enter Configuration Mode:
* Begin by entering the global configuration mode to make changes to the switch configuration.
* Create VRF "VrfGreen":
* Use the command ip vrf VrfGreen to create a new VRF named "VrfGreen". This command sets up a new VRF instance which will isolate the routing table for this VRF from the global routing table and other VRFs.
* Configure the Static Route:
* Use the command ip route vrf VrfGreen 172.16.128.64/28 10.10.10.1 213 to configure the static route.
* ip route vrf VrfGreen specifies that the route should be added to the "VrfGreen" VRF.
* 172.16.128.64/28 is the destination network.
* 10.10.10.1 is the next-hop IP address.
* 213 is the administrative distance, which in this case is set to a non-default value to influence route preference.
* Save Configuration:
* Save the configuration to ensure the changes persist after a reboot using the write memory command.
References:
* Dell Technologies Networking - SONiC
* Dell Enterprise SONiC Deployment Guide
These steps provide a comprehensive guide to configure a VRF and a static route within that VRF on a SONiC-based switch, ensuring the specific requirements for routing and administrative distance are met.
NEW QUESTION # 33
A deployment requires routing and dynamic access control lists. What bundle must be used for this deployment?
- A. Enterprise Standard
- B. Enterprise Standard
- C. Cloud Premium
- D. Edge Standard
Answer: A
Explanation:
For a deployment that requires routing and dynamic access control lists, the appropriate bundle to use is the Enterprise Standard bundle. This bundle includes advanced routing capabilities and supports dynamic access control lists for comprehensive network management and security.
References:
* Dell Technologies SONiC documentation
* Dell Networking Bundle Configuration Guide
NEW QUESTION # 34
What is the correct order of steps for data flow in asymmetric IRB frame encapsulation?
Answer:
Explanation:
Explanation:
* Ingress VTEP performs a route lookup that is based on the destination IP address.
* Ingress VTEP encapsulates the packet with VXLAN and sends it on the appropriate VNI segment.
* Egress VTEP determines that the host is local to the VNI and switches the packet.
* Egress VTEP bridges the packet after decapsulation.
Steps and Correct Order:
* Ingress VTEP performs a route lookup that is based on the destination IP address.
* The ingress VTEP (Virtual Tunnel Endpoint) first needs to determine the next hop for the packet.
This involves performing a route lookup using the destination IP address.
* Ingress VTEP encapsulates the packet with VXLAN and sends it on the appropriate VNI segment.
* Once the route lookup is complete, the ingress VTEP encapsulates the packet in a VXLAN header, which includes the appropriate VNI (VXLAN Network Identifier) segment, and forwards it.
* Egress VTEP determines that the host is local to the VNI and switches the packet.
* The egress VTEP receives the encapsulated VXLAN packet, decapsulates it, and then checks its local VNI to determine if the destination host is within the same VNI.
* Egress VTEP bridges the packet after decapsulation.
* After determining the destination host's locality, the egress VTEP bridges the packet to the appropriate interface to deliver it to the final destination.
References:
* Dell Technologies Networking - SONiC
* Dell Enterprise SONiC Deployment Guide
These steps provide a comprehensive guide to understand the correct order of operations in asymmetric IRB (Integrated Routing and Bridging) frame encapsulation within a VXLAN environment.
NEW QUESTION # 35
How many port channels can be assigned to a single port?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
Explanation:
According to the Dell SONiC documentation, a single physical port can be a member of only one port channel at a time. This restriction ensures the consistency and integrity of link aggregation configurations.
References:
* Dell Networking SONiC: How to Configure Port Channels
* Dell Technologies InfoHub
NEW QUESTION # 36
What is a correct use-case scenario for ZTP in Enterprise SONiC?
- A. The user wants to configure the switch manually using the CLI.
- B. The user wants single pane of glass monitoring.
- C. The user wants multivendor switch deployment.
- D. The user wants to replace a failed unit and use an automatic script.
Answer: D
Explanation:
ZTP (Zero Touch Provisioning) is used to automate the configuration of switches, especially useful in scenarios where a failed unit needs to be replaced. By using ZTP, the switch can automatically download and apply the necessary configuration scripts upon boot-up, reducing the need for manual intervention and speeding up the deployment process.
References:
* Dell Technologies SONiC documentation
* Zero Touch Provisioning Guide
NEW QUESTION # 37
What are three characteristics of VLAN translation?
- A. By default, VLAN stacking is enabled on Z9432F-ON switches.
- B. SVLAN configuration for both Q-in-Q VLAN tunneling and VLAN translation is possible on the same interface.
- C. VLAN translation is not supported on MC-LAG port channel interfaces.
- D. Trunk or access ports can be configured as members of any VLANs that are not used as an SVLAN.
- E. The SVLAN header is replaced with a VNI if the provider network uses a VXLAN overlay.
Answer: B,C,D
Explanation:
* VLAN translation is not supported on MC-LAG port channel interfaces (A): This is a restriction commonly seen in network configurations involving Multi-Chassis Link Aggregation (MC-LAG) where VLAN translation capabilities are not applied.
* Trunk or access ports can be configured as members of any VLANs that are not used as an SVLAN (B): This ensures that the VLAN configuration on trunk or access ports is flexible and does not overlap with Service VLANs (SVLANs).
* SVLAN configuration for both Q-in-Q VLAN tunneling and VLAN translation is possible on the same interface (E): This allows for complex VLAN tagging and translation configurations to be applied to the same interface, supporting advanced networking scenarios.
References:
* Dell Technologies SONiC documentation
* Dell Networking Configuration Guide
NEW QUESTION # 38
What is an iBGP neighbor relationship?
- A. Two BGP neighbors share L2VPN EVPN advertisements.
- B. Two BGP neighbors have the same autonomous system numbers
- C. Two BGP neighbors share only private networks.
- D. Two BGP neighbors share only native BGP networks.
Answer: B
Explanation:
An iBGP (Internal Border Gateway Protocol) neighbor relationship is established between two BGP routers within the same autonomous system (AS). This relationship allows for the exchange of routing information within the AS, ensuring that internal routes are propagated correctly.
References:
* Dell Technologies SONiC Routing Guide
* BGP Configuration Guide
NEW QUESTION # 39
Refer to the exhibit.
What is the purpose of the static route?
- A. Verify that the 12.0.0.0 network is active and reachable.
- B. Provide a route to the 12.0.0.0 network.
- C. Provide a route to the 192.168.45.0 network.
- D. Verify that devices in VLAN 45 are reachable.
Answer: B
Explanation:
The static route shown in the exhibit S* 12.0.0.0/16 via 192.168.45.254 Vlan45 is used to provide a route to the 12.0.0.0 network. This static route directs traffic destined for the 12.0.0.0/16 network through the gateway at 192.168.45.254, which is associated with VLAN 45. This configuration is typically used to ensure that traffic can reach a specific network via a defined path.
References:
* Dell Technologies SONiC Routing Guide
* Dell Networking Configuration Guide
NEW QUESTION # 40
What is a correct use-case scenario for ZTP in Enterprise SONiC?
- A. The user wants to configure the switch manually using the CLI.
- B. The user wants single pane of glass monitoring.
- C. The user wants multivendor switch deployment.
- D. The user wants to replace a failed unit and use an automatic script.
Answer: D
NEW QUESTION # 41
Which two additional Q-in-Q VLAN tunnel configuration steps must be followed if the provider network uses a VXLAN overlay?
- A. Remove the CVLAN-to-SVLAN mapping.
- B. Configure the BGP route-target and route-distinguisher.
- C. Map the SVLAN traffic to a VNI.
- D. Configure VLAN Translation.
Answer: C,D
Explanation:
* Configure VLAN Translation (A): VLAN translation is necessary to translate customer VLANs (CVLANs) to service VLANs (SVLANs) for Q-in-Q tunneling in a VXLAN environment.
* Map the SVLAN traffic to a VNI (B): SVLAN traffic must be mapped to a VXLAN Network Identifier (VNI) for encapsulation and transport across the VXLAN overlay network.
References:
* Dell Technologies SONiC documentation
* VXLAN Configuration Guide
NEW QUESTION # 42
What are the supported modes for the QSFP28 ports on an S5248F?
- A. 1x100G, 1x40 G, 4x25 G, and 4x10 G
- B. 1x200G, 1x100 G, 1x40 G, and 4x25 G
- C. 1x100G, 1x40 G, 2x50 G, and 4x25 G
- D. 1x400G, 2x200 G, 4x25 G. and 4x10 G
Answer: C
Explanation:
The QSFP28 ports on an S5248F switch support multiple modes, including 1x100G, 1x40G, 2x50G, and
4x25G. These modes provide flexibility in network design and enable the switch to support different types of network connections and bandwidth requirements.
References:
* Dell S5248F Switch Data Sheet
* Dell Technologies InfoHub
NEW QUESTION # 43
VLAN 40 is configured in Switch A with an anycast-address of 192.168.40.254/24. The ARP neighbor suppression is enabled. Use the simulator to create a VTEP named vtep1 and assign an IP address of
10.10.10.1. Map the VNI 400 to VLAN 40.
Answer:
Explanation:
see the explanation for all step by step solution with all explanation.
Explanation:
Here are the steps to create the VTEP and map the VNI to the VLAN:
* Enter Configuration Mode:
SwitchA# configure terminal
* Create VTEP Interface:
SwitchA(config)# interface vtep1
SwitchA(config-if-vtep1)# ip address 10.10.10.1/24
SwitchA(config-if-vtep1)# exit
* Map VNI 400 to VLAN 40:
SwitchA(config)# vlan 40
SwitchA(config-vlan)# vn-segment 400
SwitchA(config-vlan)# exit
* Enable ARP Neighbor Suppression:
SwitchA(config)# interface Vlan40
SwitchA(config-if-Vlan40)# ip address 192.168.40.254/24
SwitchA(config-if-Vlan40)# vxlan arp-suppression
SwitchA(config-if-Vlan40)# exit
* Save Configuration:
SwitchA# write memory
* Enter Configuration Mode:
* Begin by entering the global configuration mode to make changes to the switch configuration.
* Create VTEP Interface:
* Enter the interface configuration mode for the VTEP interface named vtep1 using interface vtep1.
* Assign the IP address 10.10.10.1/24 to the VTEP interface using the ip address command.
* Exit the interface configuration mode.
* Map VNI 400 to VLAN 40:
* Enter the VLAN configuration mode for VLAN 40 using vlan 40.
* Map the VNI 400 to VLAN 40 using the vn-segment 400 command.
* Exit the VLAN configuration mode.
* Enable ARP Neighbor Suppression:
* Enter the interface configuration mode for VLAN 40 using interface Vlan40.
* Assign the anycast IP address 192.168.40.254/24 to the VLAN interface using the ip address command.
* Enable ARP neighbor suppression using the vxlan arp-suppression command.
* Exit the interface configuration mode.
* Save Configuration:
* Save the configuration to ensure the changes persist after a reboot using the write memory command.
References:
* Dell Technologies Networking - SONiC
* Dell Enterprise SONiC Deployment Guide
These steps provide a comprehensive guide to configure a VTEP and map the VNI to VLAN 40 on Switch A, ensuring the specific requirements for IP addressing and ARP neighbor suppression are met.
NEW QUESTION # 44
An administrator is installing Enterprise SONIC in ONIE from an HTTP server.
On which interface should the administrator configure the IP?
- A. Eth1/1
- B. ethO
- C. Mgmt1/1/1
- D. GiO
Answer: B
Explanation:
When installing Enterprise SONIC from an HTTP server using the Open Network Install Environment (ONIE), the management interface typically used for network installations is eth0. This is the default interface ONIE uses for network connectivity to retrieve installation images and other configuration files.
References:
* Dell Technologies SONiC documentation
* ONIE User Guide
NEW QUESTION # 45
......
D-SNC-DY-00 Dumps are Available for Instant Access: https://www.lead1pass.com/EMC/D-SNC-DY-00-practice-exam-dumps.html
Valid D-SNC-DY-00 Dumps for Helping Passing D-SNC-DY-00 Exam!: https://drive.google.com/open?id=1SGubPuztGvJe_AP6CexLS5A5hZAnDnqs