2024 Valid 300-615 Real Exam Questions (Updated) 100% Dumps & Practice Exam
[UPDATED 2024] Cisco 300-615 Questions Prepare with Free Demo of PDF
Cisco 300-615 exam is ideal for professionals who are working in the field of networking and want to enhance their skills and knowledge. Troubleshooting Cisco Data Center Infrastructure certification is also suitable for individuals who are looking to start a career in networking. Troubleshooting Cisco Data Center Infrastructure certification program is recognized globally and can help individuals secure better job opportunities, higher salaries, and promotions.
NEW QUESTION # 114
Refer to the exhibits.
An engineer troubleshoots switch N5K1, which fails to receive traffic from the file server Which set of actions resolves this problem?
- A. Bind native VLAN 10 with Ethemet1/10 and allow VSAN 101 in trunk configuration.
- B. Assign native VLAN 10 with vfc111 and allow VLAN 1101 in trunk configuration.
- C. Bind native VLAN 10 with Ethemet10/1/1 and allow VLAN 10 in trunk configuration
- D. Assign native VLAN 10 with fc2.'l - 2 and allow VLAN 10 in trunk configuration.
Answer: A
NEW QUESTION # 115
Refer to the exhibit.
The HSRP configuration in the exhibit fails to function. Which action resolves this issue?
- A. Enable IP redirects.
- B. Set the MTU to 1500 bytes.
- C. Configure the same HSRP group on both devices.
- D. Configure HSRP version 2.
Answer: A
NEW QUESTION # 116
An engineer deploys a Cisco fabric network based on spine-leaf architecture. Cisco DCNM has been integrated to support the automation of a virtual network service of a firewall. After integration, the engineer observes that the host traffic does not reach the firewall node. Which action resolves the issue?
- A. Delete the service node IP address in DCNM.
- B. Configure the required profile for the host network.
- C. Complete the service configuration parameters.
- D. Update the host node IP address in DCNM.
Answer: C
NEW QUESTION # 117 
Refer to the exhibit. A network engineer configures an EEM script to get a syslog notification after a configuration change. This message appears when the engineer must make a new configuration to this switch. Which configuration did the engineer neglect to apply in the script for it to function properly?
- A. action 2.0 event-default
- B. event syslog occurs 10
- C. event cli match 'configure terminal'
- D. event policy-default count 1 time 100
Answer: A
Explanation:
Section: Automation
NEW QUESTION # 118 
Refer to the exhibit. An OSPF adjacency between Router-A and Router-B cannot reach the FULL state. Which action resolves the issue?
- A. Set the OSPF media type to point-to-point.
- B. Disable the check of the MTU value.
- C. Adjust the MTU on Router-A to 1600.
- D. Adjust the MTU on Router-B to 1604.
Answer: B
Explanation:
Section: Network
NEW QUESTION # 119
A system administrator adds two vNICs to an existing service profile that is used to run a vSphere environment to support disjoint Layer 2 network connectivity. However, after the server is rebooted, the host is not accessible on the network Which action resolves the issue?
- A. Remove all existing vNICs and add them in the desired order.
- B. Build a new service profile with the desired network configuration
- C. Add the disjoint Layer 2 VLANs to an existing vNIC rather than adding new vNICs
- D. Create a vNIC placement policy to avoid adapter renumbering
Answer: D
NEW QUESTION # 120
Refer to the exhibit.
An engineer is investigating a role mapping issue on a switch. The users report that they cannot view the IP addresses under the tenant "corp". Which action resolves the issue?
- A. Update the UNIX ID.
- B. Configure the correct secret password between the APIC and the RADIUS server.
- C. Add the users to the RADIUS server.
- D. Add the updated avpair to include/corp/admin/
Answer: B
NEW QUESTION # 121 
Refer to the exhibit. A functioning trunk port Ethernet1/48 exists between two identical Cisco Nexus 5000 Series Switches. The interfaces on the switches support the MACsec feature and are configured identically. To enable manual MACsec, an engineer adds the configuration shown in the exhibit to both sides of the trunk.
The trunk port stops functioning. Which action should be taken to resolve the issue?
- A. Enable the license for the trunk ports to support MACsec
- B. Disable and then enable the port
- C. Lower the MTU value to less than 9216 bytes
- D. Configure the PMK with a length of 2048 bytes
Answer: A
NEW QUESTION # 122
Drag and drop the actions from the left onto the faults that they resolve on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION # 123
Refer to the exhibit. An engineer troubleshoots an OSPF neighborship problem between Router R2 and Router R10. Which action resolves the problem?
- A. Resolve unicast reply from Router R2
- B. Resolve authentication type on Router R10
- C. Change area ID on Router R10
- D. Change router ID on Router R10
Answer: A
NEW QUESTION # 124
Refer to the exhibit.
A customer network uses OSPFv2 and MP-BGP protocols A network administrator installs a new Cisco Nexus Switch in the data center but experiences a BGP RIB failure Which action solves the issue?
- A. Implement next-hop-self
- B. Configure the route as a BGP backdoor
- C. Change the administrative distance of OSPF to 220
- D. Use a filter list for OSPF to filter both routes
Answer: A
NEW QUESTION # 125
Refer to the exhibit. A network administrator created an EEM script to alert network management about flapping interfaces on a Cisco Nexus Series Switch. The applet must run when an interface flaps three times within 10 minutes. The EEM script fails to run as expected. Which action resolves the issue?
- A. Change the event period to 600.
- B. Configure a policy-default action.
- C. Use integer data within the SNMP trap.
- D. Associate a scheduler to the EEM script.
Answer: A
NEW QUESTION # 126
Refer to the exhibit. A network engineer is configuring the FCoE N_Port virtualization storage area network. After the initial implementation, server 11 fails to connect to the disk array. Which action resolves the issue?
- A. On N9K interface vfc11, change switchport mode configuration to NP
- B. On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to F
- C. On MDS interface vfc 1/1, change switchport mode configuration to VF
- D. On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to E
Answer: D
NEW QUESTION # 127
Refer to the exhibit.
An upgrade operation fails with an error displayed. Which action resolve the issue?
- A. Use a different kickstart image
- B. Allocate extra space on a flash drive to extract a kickstart image
- C. Use a different system image
- D. Allocate extra space on a flash drive to extract a system image
Answer: C
Explanation:
Explanation
Kickstart image verification succeeded. System image has failed.
NEW QUESTION # 128
Refer to the exhibit.
The scheduler was configured to save the running-config automatically daily. However, the scheduler is returning the error presented. Which action resolves the issue?
- A. Remove vrf management from the command
- B. Reconfigure the scheduler using the admin user
- C. Use the kstack attribute for copying the configuration file
- D. Change the file transfer protocol to TFTP in scheduler job
Answer: D
NEW QUESTION # 129
Drag and drop the commands from the left onto the correct categories on the right.
Answer:
Explanation:
NEW QUESTION # 130
An engineer experiences an issue presented with the Cisco ucs system. Which action resolves the issue?
- A. Connect the adapter to the fabric interconnects using a breakout cable.
- B. Update the 1/O module firmware on the Cisco UCS chassis.
- C. Change the discovery policy backplane speed preference to 4x10G.
- D. Reboot the blade server and acknowledge the fault.
Answer: C
NEW QUESTION # 131
Refer to the exhibit.
An engineer fails to implement a Cisco UCS Manager integration manager. The credentials and IP connectivity between Cisco APIC and UCS Manager are configured as expected. Which action resolves the issue?
- A. Install ExternalSwitch app in the APIC controller
- B. Enable JSON API on the Cisco UCS Manager
- C. Change the Integration Manager name to FQDN of the Cisco UCS Manager
- D. Disable HTTP to HTTPS redirection in Cisco UCS Manager
Answer: A
NEW QUESTION # 132
A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue?
- A. 1. Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
2. Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3. Check for runtime link down status.
4. Reseat the affected IOM. - B. 1. Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2. Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3. Check for runtime link down status.
4. Reseat the affected IOM. - C. 1. Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
2. Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3. Check for runtime link down status.
4. Reseat the affected IOM. - D. 1. Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2. Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3. Check for runtime link down status.
4. Reseat the affected IOM.
Answer: B
Explanation:
Section: Compute Platforms
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ts/guide/UCSTroubleshooting/ UCSTroubleshooting_chapter_01001.html
NEW QUESTION # 133
A system administrator adds two vNICs to an existing service profile that is used to run a vSphere environment to support disjoint Layer 2 network connectivity. However, after the server is rebooted, the host is not accessible on the network Which action resolves the issue?
- A. Add the disjoint Layer 2 VLANs to an existing vNIC rather than adding new vNICs
- B. Remove all existing vNICs and add them in the desired order.
- C. Build a new service profile with the desired network configuration
- D. Create a vNIC placement policy to avoid adapter renumbering
Answer: A
NEW QUESTION # 134
Refer to the exhibit. An engineer fails to install Perl in the guest shell on a Cisco Nexus 9000 Series Switch.
Which two actions must be taken in the guest shell to resolve the issue? (Choose two.)
- A. Configure domain-name and nameserver under the management VRF.
- B. Add a default gateway and nameserver.
- C. Export the http_proxy and https_proxy environment variables
- D. Add the DNS server and suffix.
- E. Install the unbound resolver package using curl.
Answer: A,D
NEW QUESTION # 135
Refer to the exhibit. The expected routes are not being leaked as expected from VRF RED to VRF BLUE. Which action resolves the issue?
- A. Set the community to 65000:65000 under the route map.
- B. Configure VRF BLUE under the BGP configuration.
- C. Include the "le 32" knob under the RED_TO_BLUE_ACL prefix list.
- D. Change the route targets under the VRFs.
Answer: A
NEW QUESTION # 136
Drag and drop the commands from the left onto the correct categories on the right.
Answer:
Explanation:
NEW QUESTION # 137
Which control plane is used according to this output?
- A. flood-and-learn MAC address learning
- B. flood-and-learn IP address learning
- C. BGP EVPN
- D. VXLAN OAM
Answer: C
NEW QUESTION # 138
Refer to the exhibit.
A network engineer configures an EEM script to get a syslog notification after a configuration change. This message appears when the engineer must make a new configuration to this switch. Which configuration did the engineer neglect to apply in the script for it to function properly?
- A. action 2.0 event-default
- B. event syslog occurs 10
- C. event cli match 'configure terminal'
- D. event policy-default count 1 time 100
Answer: A
NEW QUESTION # 139
......
300-615 Deluxe Study Guide with Online Test Engine: https://www.lead1pass.com/Cisco/300-615-practice-exam-dumps.html
NEW 2024 Certification Sample Questions 300-615 Dumps & Practice Exam: https://drive.google.com/open?id=1at_gGxH22w4yiT8W3zTmeUMvIq1H_xlX